Crush Concrete and Asphalt On Site. Reuse More of What You Already Have.

Concrete containing some reinforcing steel can be processed, but RubbleCrusher recommends removing as much rebar and other tramp metal as practical before crushing. Rebar can jam the crushing process or damage equipment if excessive or improperly prepared. The RC-J65's overband magnet helps remove smaller ferrous pieces that pass through the crusher, but it is not a substitute for proper feed preparation.

The jaw opening is 26 x 14 in (650 x 350 mm). A single maximum lump of approximately 20 x 11 in (500 x 280 mm) can physically enter the chamber, but RubbleCrusher recommends feeding 12 in minus material for consistent production and reduced wear. Oversize material slows production, increases jaw plate wear, and risks bridging. Break or shear oversized material before feeding.

The manufacturer rates the RC-J65 at 5 to 50 metric tonnes per hour (approximately 5.5 to 55 U.S. short tons per hour). Actual production varies significantly based on material type, feed size, moisture, reinforcement, feed consistency, output setting, operator practice, and site conditions. A contractor feeding clean, properly sized material at a steady rate will see very different results than one feeding irregular, wet, or oversized material intermittently.

The jaw crusher discharge setting is adjustable, which controls the maximum size of the crushed product. The actual gradation of the finished material depends on the feed material, the discharge setting, and how the material fractures. For projects requiring material separated into specific size ranges, adding the RC-S48 screening plant after the crusher allows material to be screened into up to three products. Whether the finished material satisfies a particular engineering or agency specification depends on the material, crusher settings, screen media, project requirements, and testing.

The RC-J65 can be fed with an appropriately sized excavator or skid-steer loader. The best setup depends on your material, bucket size, feed preparation, production goals, and jobsite layout. Equipment that cannot maintain a steady feed can limit production, while unnecessarily large support equipment may be inefficient for a compact crusher. Four Corners Equipment can review the complete feeding workflow with you before purchase.

At approximately 11,000 lb, the RC-J65 is designed as a compact, portable crusher that can be moved between jobsites considerably more easily than a full-size crushing spread. The appropriate truck, trailer, axle configuration, and any permitting requirements depend on the transport equipment being used and the jurisdictions involved. Verify trailer capacity, truck ratings, axle loading, total combination weight, and applicable transportation regulations before moving the machine.

Four Corners Equipment is based in Farmington, New Mexico, roughly 250 miles and a 3.5-hour drive from Santa Fe. The listed equipment price includes delivery to the buyer and on-site operator training on the day of delivery, regardless of distance. For ongoing parts, service, technical support, or field-service options at your location, call 505-329-6600 and we will review what support is available for your specific equipment and area. We serve equipment buyers across the Southwest and Mountain States and coordinate service for customers outside Farmington regularly.

Most Santa Fe contractors haul construction debris to the Caja del Rio Landfill at $52.50 to $62.50 per ton. The Buckman Road Recycling and Transfer Station (BuRRT) accepts concrete and asphalt but only in pieces under 2 x 2 feet and in loads under 12,500 lbs. Santa Fe County convenience centers prohibit construction and demolition debris entirely. The nearest concrete recycling facilities are in Albuquerque, 64 miles from Santa Fe. A compact on-site crusher lets you process suitable material where it is generated instead of hauling it to one of these facilities.

NMDOT Standard Specification Section 302 explicitly allows crushed Portland cement concrete as aggregate base course material, provided the material meets the required gradation, LA Abrasion, R-value, and other engineering requirements. Whether recycled aggregate is permitted on a specific project depends on the project specifications, the engineer of record, and any applicable agency requirements. Always confirm that your crushed material meets the specification before placing it.

Contact Four Corners Equipment to discuss the current machine location, availability, and inspection options. Depending on the machine and current operating circumstances, we can discuss whether an in-person inspection or demonstration can be arranged. Call 505-329-6600 or use the quote form on this page to start the conversation.

The listed equipment price includes delivery to the buyer and on-site operator training on the day of delivery. Introductory training covers basic operation, controls, startup, shutdown, and safe operating considerations with the buyer's personnel. This is introductory equipment orientation, not comprehensive operator certification or formal safety training. Operators should read the manufacturer's manual and follow all safety procedures.

Parts, wear items, service options, and applicable warranty coverage should be reviewed as part of the purchase process. Jaw plates and other wear components are consumable items whose replacement intervals depend on the material being processed and machine usage. Contact Four Corners Equipment at 505-329-6600 for current warranty information, parts availability, and service options for your location.

Yes. Four Corners Equipment works with multiple commercial equipment financing providers. Canon Financial Services is one of our featured financing options, and additional financing programs are available through our other lending partners. Approval, rates, down payment requirements, and terms depend on the buyer, equipment, and lender. Explore commercial financing options.

The RC-J65 is the compact jaw crusher used to break down concrete, asphalt, brick, block, and selected stone. The RC-S48 is a screening plant used to separate crushed or raw material into up to three sized products, making the J65 and S48 a useful combination when both crushing and screening are required. The RC-J72 is a larger crusher designed for larger feed and higher production, with a 28 x 16 in jaw, production capacity up to approximately 90 metric tonnes per hour, and an integral vibrating grizzly feeder. The right configuration depends on your material, volume, desired output, support equipment, and budget.